TI is one of our advantageous brands. In addition to hot-selling products, we can also provide stock of shortages and discontinued products. The following are some of the products recently shipped to Italy：
① Part Number : SN74LVC125APWR
Category : Integrated Circuits (ICs) - Logic - Buffers,Drivers,Receivers,
Transceivers
Logic Type : Buffer, Non-Inverting
Number of Elements : 4
Number of Bits per Element : 1
Output Type : 3-State
Current - Output High, Low : 24mA, 24mA
Voltage - Supply : 1.65V ~ 3.6V
Operating Temperature : -40°C ~ 125°C (TA)
Features :
• 3-State outputs
• Separate OE for all 4 buffers
• Operates from 1.65V to 3.6V
• Specified from –40°C to 85°C and –40°C to 125°C
• Inputs accept voltages to 5.5V
• Max tpd of 4.8ns at 3.3V
• Typical VOLP (output ground bounce) < 0.8V at VCC = 3.3V, TA = 25°C
• Typical VOHV (output VOH undershoot) > 2V at VCC = 3.3V, TA = 25°C
• Latch-up performance exceeds 250mA per JESD 17
Applications :
• Cable Modem Termination Systems
• IP Phones: Wired and Wireless
• Optical Modules
• Optical Networking:
– EPON or Video Over Fiber
• Point-to-Point Microwave Backhaul
• Power: Telecom DC/DC Modules:
– Analog or Digital
• Private Branch Exchanges (PBX)
• TETRA Base Stations
• Telecom Base Band Units
• Telecom Shelters:
– Filter Units
– Power Distribution Units (PDU)
– Power Monitoring Units (PMU)
– Wireless Battery Monitoring
– Remote Electrical Tilt Units (RET)
– Remote Radio Units (RRU)
– Tower Mounted Amplifiers (TMA)
• Vector Signal Analyzers and Generators
• Video Conferencing: IP-Based HD
• WiMAX and Wireless Infrastructure Equipment
• Wireless Communications Testers
• xDSL Modems and DSLAM
This quadruple bus buffer gate is designed for 1.65V to 3.6V VCC operation.
The SN74LVC125A device features independent line drivers with 3-state outputs. Each output is disabled when the associated output-enable (OE) input is high.
To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver.
Inputs can be driven from either 3.3V or 5V devices.
This feature allows the use of this device as a translator in a mixed 3.3V/5V system environment.
② Part Number : ISO1050DUBR
Category : Integrated Circuits (ICs) - Interface - Drivers, Receivers, Transceivers
Type : Transceiver, Isolated
Protocol : CANbus
Number of Drivers/Receivers : 1/1
Duplex : Half
Receiver Hysteresis : 150 mV
Data Rate : 1Mbps
Voltage - Supply : 3V ~ 5.5V
Operating Temperature : -55°C ~ 105°C
Applications :
• Industrial automation, control, sensors, and drive systems
• Building and climate control (HVAC) automation
• Security systems
• Transportation
• Medical
• Telecom
• CAN bus standards such as CANopen, DeviceNet, NMEA2000, ARINC825, ISO11783, CAN Kingdom, CANaerospace
The ISO1050 is a galvanically isolated CAN transceiver that meets the specifications of the ISO11898-2 standard. The device has the logic input and output buffers separated by a silicon oxide (SiO2) insulation barrier that provides galvanic isolation of up to 5000 VRMS for ISO1050DW and 2500 VRMS for ISO1050DUB. Used in conjunction with isolated power supplies, the device prevents noise currents on a data bus or other circuits from entering the local ground and interfering with or damaging sensitive circuitry.
As a CAN transceiver, the device provides differential transmit capability to the bus and differential receive capability to a CAN controller at signaling rates up to 1 megabit per second (Mbps). The device is designed for operation in especially harsh environments, and it features cross-wire, overvoltage and loss of ground protection from –27 V to 40 V and overtemperature shutdown, as well as –12V to 12V common-mode range.
The ISO1050 is characterized for operation over the ambient temperature range of –55°C to 105°C.
③ Part Number : LM321MFX/NOPB
Category : Integrated Circuits (ICs) - Linear Amplifiers - Instrumentation, OP Amps, Buffer Amps
Amplifier Type : General Purpose
Number of Circuits : 1
Slew Rate : 0.4V/µs
Gain Bandwidth Product : 1 MHz
Current - Input Bias : 45 nA
Voltage - Input Offset : 2 mV
Current - Supply : 660µA
Current - Output / Channel : 40 mA
Voltage - Supply Span (Min) : 3 V
Voltage - Supply Span (Max) : 32 V
Operating Temperature : -40°C ~ 85°C
Applications :
• Chargers
• Power Supplies
• Industrial: Controls, Instruments
• Desktops
• Communications Infrastructure
The LM321 brings performance and economy to low power systems. With a high unity gain frequency and a specified 0.4-V/µs slew rate, the quiescent current is only 430-µA/amplifier (5 V). The input common mode range includes ground and therefore the device is able to operate in single supply applications as well as in dual supply applications. It is also capable of comfortably driving large capacitive loads.
The LM321 is available in the SOT-23 package Overall the LM321 is a low power, wide supply range performance operational amplifier that can be designed into a wide range of applications at an economical price without sacrificing valuable board space.
④ Part Number : LM336MX-2.5/NOPB
Category : Integrated Circuits (ICs) - Power Management (PMIC) - Voltage Reference
Voltage - Output (Min/Fixed) : 2.49V
Current - Output : 10 mA
Tolerance : ±4%
Current - Cathode : 400 µA
Operating Temperature : 0°C ~ 70°C (TA)
Features :
• Low temperature coefficient
• Wide operating current of 400 μA to 10 mA
• 0.2Ω dynamic impedance
• ± 1% initial tolerance available
• Guaranteed temperature stability
• Easily trimmed for minimum temperature drift
• Fast turn-on
The LM136-2.5/LM236-2.5 and LM336-2.5 integrated cir- cuits are precision 2.5V shunt regulator diodes. These monolithic IC voltage references operate as a low-temperature-coefficient 2.5V zener with 0.2Ω dynamic im-pedance. A third terminal on the LM136-2.5 allows the refer-ence voltage and temperature coefficient to be trimmed easily.
The LM136-2.5 series is useful as a precision 2.5V low voltage reference for digital voltmeters, power supplies or op amp circuitry. The 2.5V make it convenient to obtain a stable reference from 5V logic supplies. Further, since the LM136- 2.5 operates as a shunt regulator, it can be used as either a positive or negative voltage reference.
The LM136-2.5 is rated for operation over −55℃ to +125℃ while the LM236-2.5 is rated over a −25℃ to +85℃ tem- perature range
The LM336-2.5 is rated for operation over a 0℃ to +70℃ temperature range.
⑤ Part Number : CDCLVC1103PWR
Category : Integrated Circuits (ICs) - Clock/Timing - Clock Buffers, Drivers
Type : Fanout Buffer (Distribution)
Number of Circuits : 1
Ratio - Input:Output : 1:3
Differential - Input:Output : No/No
Input : LVCMOS
Output : LVCMOS
Frequency - Max : 250 MHz
Voltage - Supply : 2.3V ~ 3.6V
Operating Temperature : -40°C ~ 85°C
Features :
• High-Performance 1:2, 1:3, 1:4, 1:6, 1:8, 1:10,1:12 LVCMOS Clock Buffer Family
• Very Low Pin-to-Pin Skew < 50 ps
• Very Low Additive Jitter < 100 fs
• Supply Voltage: 3.3 V or 2.5 V
• fmax = 250 MHz for 3.3 V
fmax = 180 MHz for 2.5 V
• Operating Temperature Range: –40°C to 85°C
• Available in 8-, 14-, 16-, 20-, 24-Pin TSSOP Package (All Pin-Compatible)
Applications :
General-Purpose Communication, Industrial, and Consumer Applications
The CDCLVC11xx is a modular, high-performance,low-skew, general-purpose clock buffer family from Texas Instruments.
The entire family is designed with a modular approach in mind. It is intended to round up TI's series of LVCMOS clock generators.
Seven different fan-out variations, 1:2 to 1:12, are available. All of the devices are pin-compatible to each other for easy handling.
All family members share the same high performing characteristics such as low additive jitter, low skew, and wide operating temperature range.
The CDCLVC11xx supports an asynchronous output enable control (1G) which switches the outputs into a low state when 1G is low.
The CDCLVC11xx family operates in a 2.5-V and 3.3-V environment and are characterized for operation from –40°C to 85°C.
⑥ Part Number:LM258ADR
Category : Integrated Circuits (ICs) - Linear Amplifiers - Instrumentation, OP Amps, Buffer Amps
Amplifier Type : General Purpose
Number of Circuits : 2
Slew Rate : 0.3V/µs
Gain Bandwidth Product : 700 kHz
Current - Input Bias : 15 nA
Voltage - Input Offset : 2 mV
Current - Supply : 500µA (x2 Channels)
Current - Output / Channel : 40 mA
Voltage - Supply Span (Min) : 3 V
Voltage - Supply Span (Max) : 32 V
Operating Temperature : -25°C ~ 85°C (TA)
Features :
• Wide supply range of 3 V to 36 V (B version)
• Quiescent current: 300 μA per amplifier (B version, typical)
• Unity-gain bandwidth of 1.2 MHz (B version)
• Common-mode input voltage range includes ground, enabling direct sensing near ground
• Low input offset voltage of 3 mV at 25°C (A and B versions, maximum)
• Internal RF and EMI filter (B version)
• On products compliant to MIL-PRF-38535, all parameters are tested unless otherwise noted. On all other products, production processing does not necessarily include testing of all parameters.
Applications :
• Merchant network and server power supply units
• Multi-function printers
• Power supplies and mobile chargers
• Motor control: AC induction, brushed DC, brushless DC, high-voltage,
low-voltage, permanent magnet, and stepper motor
• Desktop PC and motherboard
• Indoor and outdoor air conditioners
• Washers, dryers, and refrigerators
• AC inverters, string inverters, central inverters, and voltage frequency drives
• Uninterruptible power supplies
• Programmable logic controllers
• Electronic point-of-sale systems
The LM358B device are the next-generation versions of the industry-standard operational amplifiers (op amps) LM358 and LM2904, which include two high-voltage (36-V) op amps.
These devices provide outstanding value for cost- sensitive applications, with features including low offset (300 μV, typical), common-mode input range to ground, and high differential input voltage capability.
The LM358B op amps simplify circuit design with enhanced features such as unity-gain stability, lower offset voltage of 3 mV (maximum at room temperature), and lower quiescent current of 300 μA per amplifier (typical). High ESD (2 kV, HBM) and integrated EMI and RF filters enable the LM358B device to be used in the most rugged,environmentally challenging applications.
The LM358B and LM2904B amplifiers are available in industry standard packages, including SOIC, TSSOP, and VSSOP
Our Services:
1. One Year Guarantee for each part
2. Free shipping for first order under 2kg
3. Mini order from 1 pcs
4. Short lead time, Quick delivery
Looking forward to cooperate with you.Emial : [email protected]
